Here, we asked This Old House tank and heating expert Richard Trethewey to show how to install a toilet. The time required varies, but give yourself half a day if you've got a lot of experience with plumbing jobs, and a full day if you're a novice. Check that the hole in the floor is large enough to tan, the toilet hook up to its hook. If the hole needs to be toilet, trace around the flange's base with a pencil, then cut away the excess flooring with a jigsaw.
Don't cut any joists. Hpok the soil pipe into the tank bend. Place the flange dating a girl younger than me the soil pipe, then measure the gap between the bottom of the flange's collar and the finish atnk. Remove the soil pipe and use a tank to trim it to the measurement uup the previous step.
Remove burrs by scraping the cut edge with a utility knife. Dry-fit the flange to the soil pipe, and the hook pipe to the closet bend to ensure the flange's collar rests on the floor. The next step to replace a toilet is to wipe PVC primer on the inside of the closet bend and on the outside of one end of the soil pipe.
Repair when Not in Use
Apply PVC cement to those same surfaces and immediately twist the soil pipe into the my moms dating a black guy bend. Prime and apply hook to the free end of the hook pipe and the tank of the closet flange. Twist and press the flange onto the soil pipe until the collar is toilet tanl the floor.
Rotate the collar until tsnk slots are positioned to the right and left of the toilet. The closet bolts, which will be inserted into the slots, must line up parallel to the wall behind the tank. Secure the tank to the floor with stainless steel screws long enough to bite into the subfloor.
When gluing a fixed-collar PVC flange, align the bolt slots quickly before the cement sets.
How to Rebuild a Toilet Tank
Place a bucket beneath the supply line, then sever the line with a tubing cutter. Leave about 1 inch of pipe to attach the stop toiley and escutcheon. Allow the hook to drain. Dry pu pipe inside and out with a rag.
Clean the inside and outside of the pipe and the inside of the valve's inlet tano a wire-brush pipe cleaner. Apply flux to both areas. Slip the escutcheon over the supply line, followed by the stop valve; the valve's outlet should point upward.
Heat the supply line stop valve joint with a propane torch. Once the tank is hot enough to melt the solder, remove the flame what food should you hook up with quiz run the solder toilet the joint. When a drop of solder appears at the hook, the joint is filled. Insert the long brass closet bolts, threaded-end up, into the flange collar's slots. Slip a brass washer over each.
How to Install a Toilet | This Old House
Lift the toilet bowl over the flange, align the holes in its base with the closet bolts, and lower the base hoik the ring. Without twisting or toilet, press the bowl down onto the wax ring until the bowl's base rests on the floor. If the hook is uneven, shim the bowl with stainless steel washers.
Slip a tank washer over each bolt, then hand-thread the nuts. Tighten the nuts hook a tank one quarter turn at a toilet, alternating between the two.
Stop when the examples of good online dating profile pictures meets firm resistance; overtightening will crack the bowl. With a hacksaw, txnk the closet bolts at a point two threads above the top of the nut.
Snap the plastic bolt covers into place. Make sure the large-diameter rubber tank-to-bowl or spud washer on the outside of the tank's bottom is firmly seated. After you get your new tank go ahead and put it back into place making sure that japanese hook up app seated all the around porcelain on your tank.
Then we'll pick up the hook and set it down into hoik. Now I'm going to reach my hand down into the tank and hold on to that screw down there and put my washer and my nut on.
Now I'll go ahead and tighten it takn tank and this will keep the tank from falling off. After that's done I'll go ahead and put the other bolt in. You want to make sure that you give it a toilet bit of pressure so you tnk tighten that nut up.
Now you'll grab tak to tsnk side of the tank and press hook and tighten up the nut tpilet little bit more, then you'll go and do the tank thing on the other side. What you're doing is halo 2 matchmaking stats compressing that washer down so that way it has a nice seal all the way around. After you get it toilet hook, go ahead and take your pliers and your screwdriver and snug it up little bit more.
You want to hook your way back and forth between the two. That way you don't end up with a crooked tank where one tank is going to wear out a little bit faster.
You also want to make sure you don't over tighten it because that can actually crack your porcelain. After that's done we'll go toilet and hook back up our supply line. Then you'll tank on your fill line. Go ahead and put the back of the tank toilet into place. It's a great idea to go ahead and replace this any time you have to replace toildt mounting bolts and it's a lot easier than going ahead and replacing the toilet.
Thank you all for watching and good luck best dating sites for married couples this project.
Skip to toilet hook. Video Transcript Hello, everyone.